Worthington Distribution Knowledge Base

Z-Wave Shades – Zipato Micromodule Motor Controller with Zipato

Introduction:

Looking to control some shades with Z-Wave? Worthington Distribution has a solution using a Somfy standard, 4-wire, AC motor with Zipato’s Micromodule Motor Controller. This article will walk you through the shade installation as well as how to add the shade to your Zipato hub.

 

Requirements:

  • Somfy-powered shade using a standard, 4-wire, AC motor
  • Zipato Micromodule motor controller, SKU ZIPPHPAN08US
  • Zipato hub

 

Procedure:

Pre-wiring recommendations –

It’s recommended that you have your electrician run an AC wire to the left side of the window. Although a bare wire with wire nuts can be used, to pass inspection, the electrician will likely need to terminate the AC line. If there’s no room for a standard outlet, your electrician can install a Sillites self-contained receptacle, SILSCRW.

 

Install the shade per the fabricator’s instructions. Be sure that the shade is level to avoid any issues with the fabric “telescoping.”

 

Install the Zipato Micromodule Motor Controller, following the diagram below:

Please note: Z-Wave is an RF communication. If your shade has a metal fascia or a cassette, make sure that the antenna of the micromodule is outside of the metal to ensure optimal Z-Wave communication.

 

Perform the following steps to learn the micromodule into your Zipato hub:

  1. Log into the Zipato browser interface.
  2. Click on the Device Manager and select “ADD NEW DEVICE.”
  3. Select Z-Wave.
  4. While the device exclusion window is open, apply power to the micromodule. It should be detected by the Zipato. If it isn’t, quickly press the button on the module three times.
  5. The module should learn into your Wink hub. If it doesn’t, then quickly press the button on the module three times again.
  6. Name the device and click “Done.”
  7. Give the module approximately 60 seconds to complete provisioning before proceeding.
  8. Click on Open or Close to ensure that the shade moves in the correct direction.1 Also, make sure that the shade stops at the correct upper and lower limits.2

 

1 If the shade runs in reverse, power down the micromodule and swap the red and black wires coming from the motor. Make sure to re-apply power once the wires have been swapped.

2 If the limits need to be adjusted, refer to the shade fabricator’s or the motor manufacturer’s instructions.

 

Once you’re certain that the directions and limits are correct, you will need to calibrate the micromodule to the shade. To do so, press and hold the button on the micromodule for 3-5 seconds and then release it. The shade will move up and down several times so that the module can learn its upper and lower limits.

 

Repeat these steps for any additional shades and micromodules you would like to control.

 

Results:

You will now have full control of the shade with your Z-Wave controller. To confirm, press Open, Close, or move to % to verify that the treatment now moves to this position.

Attached Files
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Name
Email
Security Code Security Code
Related Articles RSS Feed
Z-Wave Shades – Zipato Micromodule Motor Controller with Vera Controls
Viewed 3184 times since Wed, Jul 12, 2017
Using the Aeotec Wallmote with SmartThings
Viewed 16421 times since Tue, Mar 21, 2017
Z-Wave Shades – Zipato Micromodule Motor Controller with Fibaro
Viewed 2342 times since Wed, Jul 12, 2017
How to create a Z-Wave network with the Leviton VRC0P-1LZ
Viewed 7236 times since Tue, Jul 26, 2016
Wink: detect a water leak > sound a sounder and notify a user
Viewed 3447 times since Thu, May 18, 2017
ESI RP Programming Example – Calibrating Motor Controllers
Viewed 2213 times since Thu, Apr 28, 2016
Resetting a Somfy 110VAC RTS Motor and Setting Limits in Program Mode
Viewed 9568 times since Fri, May 6, 2016
Zipato Z-wave Water/Gas Valve Controller and water sensing.
Viewed 3664 times since Tue, Apr 19, 2016
ESI QSIB Hookup and Programming
Viewed 2605 times since Thu, Jun 22, 2017
Adding Somfy RTS Treatments to a Z-Wave Network
Viewed 7306 times since Mon, Apr 24, 2017
MENU