Worthington Distribution Knowledge Base

Z-Wave Shades – Zipato Micromodule Motor Controller with Wink

Introduction:

Looking to control some shades with Z-Wave? Worthington Distribution has a solution using a Somfy standard, 4-wire, AC motor with Zipato’s Micromodule Motor Controller. This article will walk you through the shade installation as well as how to add the shade to your Wink hub.

 

Requirements:

  • Somfy-powered shade using a standard, 4-wire, AC motor
  • Zipato Micromodule motor controller, SKU ZIPPHPAN08US
  • Wink hub

 

Procedure:

Pre-wiring recommendations –

It’s recommended that you have your electrician run an AC wire to the left side of the window. Although a bare wire with wire nuts can be used, to pass inspection, the electrician will likely need to terminate the AC line. If there’s no room for a standard outlet, your electrician can install a Sillites self-contained receptacle, SILSCRW.

 

Install the shade per the fabricator’s instructions. Be sure that the shade is level to avoid any issues with the fabric “telescoping.”

 

Install the Zipato Micromodule Motor Controller, following the diagram below:

Please note: Z-Wave is an RF communication. If your shade has a metal fascia or a cassette, make sure that the antenna of the micromodule is outside of the metal to ensure optimal Z-Wave communication.

 

Perform the following steps to learn the micromodule into your Fibaro hub:

  1. Open the Wink app.
  2. Swipe to the left menu and tap on “+ Add a Product.”.
  3. Tap Lighting, Blinds, and then Generic Z-Wave Shade.
  4. Tap Next, Next, Next, and then Connect Now.
  5. When you see “Wink hub 2 is Ready” and there is a circle on the screen, apply power to the micromodule. It should learn into your Wink hub.1
  6. Name the device and tap “Done.”
  7. Give the module approximately 60 seconds to complete provisioning before proceeding.
  8. Click on Open or Close to ensure that the shade moves in the correct direction.2 Also, make sure that the shade stops at the correct upper and lower limits.3

 

1 If the micromodule has already been powered or was part of a previous Z-Wave network, you will need to perform an exclusion with the Wink hub. Swipe to the left menu and tap on Hubs. Then swipe to the right menu and select your Wink hub. Tap on Z-Wave Controls and then Exclusion Mode. While the light on the wink hu is blinking, quickly press the button on the micromodule three times. You will then need to press the button on the micromodule three times while on step 5 of these instructions.

2 If the shade runs in reverse, power down the micromodule and swap the red and black wires coming from the motor. Make sure to re-apply power once the wires have been swapped.

3 If the limits need to be adjusted, refer to the shade fabricator’s or the motor manufacturer’s instructions.

 

Once you’re certain that the directions and limits are correct, you will need to calibrate the micromodule to the shade. To do so, press and hold the button on the micromodule for 3-5 seconds and then release it. The shade will move up and down several times so that the module can learn its upper and lower limits.

 

Repeat these steps for any additional shades and micromodules you would like to control.

 

Results:

You will now have full control of the shade with your Z-Wave controller. To confirm, press Open, Close, or move to % to verify that the treatment now moves to this position.

Attached Files
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Name
Email
Security Code Security Code
Related Articles RSS Feed
Zipato Z-wave Water/Gas Valve Controller and water sensing.
Viewed 6734 times since Tue, Apr 19, 2016
Creating a Virtual Thermostat within the Zipato interface.
Viewed 14306 times since Tue, Jul 12, 2016
Temperature sensing with the Fibaro Door/Window contact
Viewed 12150 times since Thu, Apr 21, 2016
ESI QSIB Hookup and Programming
Viewed 6526 times since Thu, Jun 22, 2017
ESI RP Programming Example – Calibrating Motor Controllers
Viewed 4845 times since Thu, Apr 28, 2016
Resetting a Somfy 24VDC RTS Motor and Setting Limits in Program Mode
Viewed 10911 times since Fri, May 6, 2016
Wink: detect a water leak > sound a sounder and notify a user
Viewed 8808 times since Thu, May 18, 2017
Z-Wave Shades – Zipato Micromodule Motor Controller with Vera Controls
Viewed 6925 times since Wed, Jul 12, 2017
How to create a Z-Wave network with the Leviton VRC0P-1LZ
Viewed 14800 times since Tue, Jul 26, 2016
Adjusting Limits on a Somfy RTS Motor
Viewed 19352 times since Fri, May 6, 2016
MENU