Worthington Distribution Knowledge Base

Z-Wave Shades – Zipato Micromodule Motor Controller with SmartThings

Introduction:

Looking to control some shades with Z-Wave? Worthington Distribution has a solution using a Somfy standard, 4-wire, AC motor with Zipato’s Micromodule Motor Controller. This article will walk you through the shade installation as well as how to add the shade to your SmartThings hub.

 

Requirements:

  • Somfy-powered shade using a standard, 4-wire, AC motor
  • Zipato Micromodule motor controller, SKU ZIPPHPAN08US
  • SmartThings hub

 

Procedure:

Pre-wiring recommendations –

It’s recommended that you have your electrician run an AC wire to the left side of the window. Although a bare wire with wire nuts can be used, to pass inspection, the electrician will likely need to terminate the AC line. If there’s no room for a standard outlet, your electrician can install a Sillites self-contained receptacle, SILSCRW.

 

Install the shade per the fabricator’s instructions. Be sure that the shade is level to avoid any issues with the fabric “telescoping.”

 

Install the Zipato Micromodule Motor Controller, following the diagram below:

Please note: Z-Wave is an RF communication. If your shade has a metal fascia or a cassette, make sure that the antenna of the micromodule is outside of the metal to ensure optimal Z-Wave communication.

 

Perform the following steps to learn the micromodule into your SmartThings hub:

  1. Open your SmartThings app.
  2. Scroll down your list of Things until you see “+ Add a Thing.” Tap on it.
  3. When you see “Looking for devices” at the top of the page and there is a cicle on the screen, apply power to the micromodule. It should learn into your SmartThings hub.1
  4. Name the device and click “Done.”
  5. Give the module approximately 60 seconds to complete provisioning before proceeding.
  6. Click on Open or Close to ensure that the shade moves in the correct direction.2 Also, make sure that the shade stops at the correct upper and lower limits.3

 

1 If the micromodule has already been powered or was part of a previous Z-Wave network, you will need to perform an exclusion with the Smartthings hub. Tap on the hamburger menu icon in the top left of the app. Tap on the hub, select Z-Wave Utilities, followed by General Z-Wave Exclusion. While it displays “Looking for devices” quickly press the button on the micromodule three times. You will then need to press the button on the micromodule three times while on step 3 of these instructions.

2 If the shade runs in reverse, power down the micromodule and swap the red and black wires coming from the motor. Make sure to re-apply power once the wires have been swapped.

3 If the limits need to be adjusted, refer to the shade fabricator’s or the motor manufacturer’s instructions.

 

Once you’re certain that the directions and limits are correct, you will need to calibrate the micromodule to the shade. To do so, press and hold the button on the micromodule for 3-5 seconds and then release it. The shade will move up and down several times so that the module can learn its upper and lower limits.

 

Repeat these steps for any additional shades and micromodules you would like to control.

 

Results:

You will now have full control of the shade with your Z-Wave controller. To confirm, press Open, Close, or move to % to verify that the treatment now moves to this position.

 

 

Attached Files
There are no attachments for this article.
Comments
There are no comments for this article. Be the first to post a comment.
Name
Email
Security Code Security Code
Related Articles RSS Feed
Resetting a Somfy 24VDC RTS Motor and Setting Limits in Program Mode
Viewed 6064 times since Fri, May 6, 2016
Z-Wave Shades – Zipato Micromodule Motor Controller with Wink
Viewed 3660 times since Wed, Jul 12, 2017
ESI RP Programming Example – Setting Group Channels
Viewed 4153 times since Thu, Apr 28, 2016
Z-Wave Shades – Zipato Micromodule Motor Controller with Vera Controls
Viewed 4398 times since Wed, Jul 12, 2017
How to create a Z-Wave network with the Leviton VRC0P-1LZ
Viewed 9646 times since Tue, Jul 26, 2016
Resetting a Somfy 110VAC RTS Motor and Setting Limits in Program Mode
Viewed 24109 times since Fri, May 6, 2016
Zipato RFID Keypad Setup
Viewed 6027 times since Fri, Apr 29, 2016
Wink: detect a water leak > sound a sounder and notify a user
Viewed 4190 times since Thu, May 18, 2017
Using the Aeotec Wallmote with SmartThings
Viewed 19108 times since Tue, Mar 21, 2017
Schlage 468 Z-Wave Lock Integration With Leviton VRC0P Serial Interface
Viewed 9784 times since Thu, Mar 9, 2017
MENU